Результаты полнотекстового поиска:
- CCS @4amps:1tu
- CCS’s) in vacuum tube amplifiers has several advantages over resistive loads. These including full mu o... ersus the diagonal line seen by resistive loaded stages. Transformer and choke loading also provides a ... signal the resistive load would give an output voltage of 188 volts P-P where the CCS load would give an output voltage of 269 volts P-P. If you compare the spacing of
- DN2540 High Voltage Constant Current Source @4amps:1tu
- ===== DN2540 High Voltage Constant Current Source ===== https://www.monoandstereo.com/2013/11/dn2540-high-voltage-constant-current.html?m=1 \\ DN2540 High Voltage Constant Current Source\\ \\ Ever dreamed of getting... ghest possible linearity out of your triode gain stage, by means of using an extremely high value of an
- DN2540 High Voltage Constant Current Source @1tubes
- ===== DN2540 High Voltage Constant Current Source ===== https://www.monoandstereo.com/2013/11/dn2540-high-voltage-constant-current.html?m=1 \\ DN2540 High Voltage Constant Current Source\\ \\ Ever dreamed of getting... ghest possible linearity out of your triode gain stage, by means of using an extremely high value of an
- LC-фильтр @4amps:6pit
- ctifier only conducts when there is a positive voltage difference between the transformer secondary and... The current drawn from the rectifier, and the voltage waveform that appears on the filter input termin... DC load current drawn from the supply. The DC voltage at the output of the filter, in turn, depends on... to say, the average value) of the filter input voltage waveform. If the average DC input voltage change
- Audio Note @4amps:8br
- load resistor, yielding a particular quiescent voltage on its anode (Vq). With a negative-going input ... d the anode swings positive due to the reduced voltage drop across the load resistor (R1 X Iq). The rev... the valve's anode current is increased so the voltage on it reduces due to increased drop across R1. ... rious with very non-linear valves and/or large voltage swings. When we want to drive a fairly meaty out
- Аудиофильская терминология @9diff
- ===== Аудиофильская терминология ===== {{tag>статьи}} https://soundex.ru/stati/analitika/audio-termins/... nd right stereo channels, which centers the soundstage and allows mono program material to image at the... ng** The placement of phantom images or spatial (stage boundary) information beyond the positional limi... which were originally located at or near center-stage. See "localization," "stereo spread." **center
- 6П21С @1tubes
- ===== 6П21С ===== {{tag>лампы пентоды выходные}} ==== Характеристики ==== {{:1tubes:6p21s.gif?direct&40... 016/02/621.html\\ http://www.bartola.co.uk/valves/tag/6p21s/\\ ==== Схемы ==== {{:1tubes:4p1l_6p21.jp... \\ \\ 6P21S with passive screen regulation, interstage trafo and ~10% Schade network. Converts what you... ut what other folks think. When you have an interstage trafo, Schade is so easy.\\ {{:1tubes:schade6p21
- Pentode with a CCS @4amps:1tu
- == Here are the results of some Pentode driver stage experiments done awhile back. The idea was to se... value larger than in traditional Pentode driver stages to get more gain.A CCS was placed in parallel w... tweaked for each tube. As adjusting the screen voltage and resistance also effects the gain of the stage you have to compromise some to have the gain match
- ES9018 @3sourse:1dacs
- ssume all ESS dac chips (9018, 9023, etc.) are VOLTAGE OUT. So, no need for I/V. Is this correct? ---- ... t, yes. ES9018 and its derivatives can support voltage mode or current mode. It depends on the input impedance where the next stage has. When it sees a low impedance, it's current mode. ES9023 has integrated amp for voltage out. I don't know if it can support current outp
- Audio-wiki
- ~~Title:Audio-wiki ~~ {{htmlmetatags>metatag-robots=() metatag-keywords=(audio,hi-fi,hi-end,tubes,amplifier,dac) metatag-description=(База данных по hi-fi и high-end ауди
- D3a @1tubes
- ===== D3a ===== {{tag>драйверные лампы пентоды}} {{:1tubes:d3a.jpg?direct&400 |}}\\ \\ ---- ==== Хар... d EC8020 for use in transformer coupled LCR phonostages. Various pentodes work very well in this phono stage topology when triode connected. I already presen... ernative which I used in two different LCR phono stage builds. The frist one can be seen here and anoth
- EML520B @1tubes
- ===== EML520B ===== {{tag> лампы выходные прямонакалы триоды}} <WRAP group> <WRAP third column> {{1... ^ 520B-V2 ^ 520B-V3 ^ 520B-V4 ^ ^ Filament Voltage (AC or DC) | = 6.5 Volt | = 5.0 Volt | = 5.0V ... Heater ( 2x 2.5V ) | ^ Tolerance on filament voltage | 5% | 5% | 5% | ^ Filament Current | ~ 1.5 Amp.... ендованная рабочая точка:** <sortable> ^ Anode Voltage | 458V | ^ Anode Dissipation | 55Watt | ^ Anod
- Formatting Syntax @wiki
- g), enclose the area either with ''%%<nowiki>%%'' tags or even simpler, with double percent signs ''<no... e used for the previous examples) or by using the tags ''%%<code>%%'' or ''%%<file>%%''. This is tex... e syntax to be highlighted is included inside the tag, e.g. ''<nowiki><code java></nowiki>'' or ''<nowi... ents by using the ''%%<html>%%'' or ''%%<php>%%'' tags. (Use uppercase tags if you need to enclose bloc
- Форматирование страниц @9diff
- g), enclose the area either with ''%%<nowiki>%%'' tags or even simpler, with double percent signs ''<no... e used for the previous examples) or by using the tags ''%%<code>%%'' or ''%%<file>%%''. This is tex... e syntax to be highlighted is included inside the tag, e.g. ''<nowiki><code java></nowiki>'' or ''<nowi... ents by using the ''%%<html>%%'' or ''%%<php>%%'' tags. (Use uppercase tags if you need to enclose bloc
- Таблица выходных ламп @1tubes
- ===== Таблица выходных ламп ===== {{tag>лампы выходные}} В списке одной строкой указаны также аналоги.... al base. It appears to have fairly low maximum voltages for plate and G2 too...\\ 6P39S is a very interesting 10W relatively low voltage but very high Gm pentode (56mA/V!) in a most cur... nds me somewhat of the EL508, but seems to have lower maximum voltages and higher plate dissipation.\\
